The screw air compressor is full of air pressure and keeps pumping What s the problem

Check the fuse, motor, and thermal relay and other equipment. Ensure that these devices are in a normal operating state. If there are problems or hidden dangers, relevant measures need to be taken to replace these devices in time. Check the pressure and temperature sensor and start button.. Check the fuse, motor, and thermal relay and other equipment. Ensure that these devices are in a normal operating state. If there are problems or hidden dangers, relevant measures need to be taken to replace these devices in time. Check the pressure and temperature sensor and start button.. A screw compressor can run loaded ('pumping air') or unloaded ('idle'). The inlet/loading valve opens and closes according to air demand. The inlet valve is controlled by a solenoid valve that supplies control air to the inlet/loading valve. Check solenoid valve coil and solenoid valve operation.. The main causes involve improper slide valve positioning, component wear, insufficient voltage, pipeline vibrations, and inadequate oil levels.. The inlet valve is controlled by a solenoid valve that supplies control air to the inlet/loading valve. Check solenoid valve coil and solenoid valve operation. First, check that there isn’t a very high air demand, or air leak somewhere. Check differential pressure over oil separator. [pdf]

Screw air compressor intake valve closes slowly

The inlet/loading valve opens and closes according to air demand. The inlet valve is controlled by a solenoid valve that supplies control air to the inlet/loading valve. Check solenoid valve coil and solenoid valve operation. First, check that there isn't a very high air demand, or air leak somewhere.. The inlet/loading valve opens and closes according to air demand. The inlet valve is controlled by a solenoid valve that supplies control air to the inlet/loading valve. Check solenoid valve coil and solenoid valve operation. First, check that there isn't a very high air demand, or air leak somewhere.. Ensure intake stop valve is fully open: Check and adjust. Excessive manual valve opening: Increases hydraulic oil flow, causing rapid movement. Adjust oil intake stop valve: Reduce flow to control movement speed. Debris in rotor grooves: Interferes with normal operation.. Intake Valve Stuck: Disassemble and clean the valve plate to remove carbon deposits (use kerosene for soaking and wiping). Check for broken cylinder diaphragms and replace with oil-resistant rubber diaphragms. [pdf]

FAQS about Screw air compressor intake valve closes slowly

What is a screw air compressor intake valve?

The intake valve of the screw air compressor is a component that controls the air pressure in the air storage tank. Commonly used intake valves have a rotating disc structure and a reciprocating valve plate mechanism. The disc or valve plate is used to open or close the air inlet to control Airflow entering the nose.

What happens if a screw air compressor is too high?

Too high is a great waste of the energy of the screw air compressor. The intake valve of the screw air compressor is a component that controls the air pressure in the air storage tank. Commonly used intake valves have a rotating disc structure and a reciprocating valve plate mechanism.

How does a compressor intake valve work?

The intake valve has two pipes, one is vented; the other is to release the remaining air in the valve to ensure normal loading of the compressor. When unloading, the current is too large, indicating that the tank pressure is high, and the opening of the intake valve is large.

How does a screw compressor work?

A screw compressor can run loaded ('pumping air') or unloaded ('idle'). The inlet/loading valve opens and closes according to air demand. The inlet valve is controlled by a solenoid valve that supplies control air to the inlet/loading valve. Check solenoid valve coil and solenoid valve operation.

Why is the intake valve not closed tightly?

It is initially suspected that the intake valve is not closed tightly, because when the air is not used, after the machine is unloaded, the pressure will slowly rise and sometimes a high-pressure alarm will be triggered!

Why is my air compressor overloaded after shutdown?

And after the shutdown, there is still some residual pressure inside the machine that cannot be discharged (About 6 kg), causing the host to be overloaded when restarting. The intake valve of the screw air compressor is a normally open intake valve.

What to do if the rock drill gets hot

First, safely remove the bit from the drill—use a cloth or gloves to avoid direct contact with the overheated metal. Inspect the bit for any visible damage such as discoloration or warping. If the bit appears to be damaged, it’s best to replace it.. First, safely remove the bit from the drill—use a cloth or gloves to avoid direct contact with the overheated metal. Inspect the bit for any visible damage such as discoloration or warping. If the bit appears to be damaged, it’s best to replace it.. Stop Using the Drill: As soon as you notice the drill overheating, stop using it immediately. Continuing to use it can cause damage to the tool and increase safety risks. Disconnect Power: Unplug the drill from the power supply.. Overheating in drills is more serious than it sounds, and you should know the correct ways to fix your tool fast. The easiest and most common ways to cool down the drill include changing the drill bit and lubricating it. It is likely time to change your drill bit when it gets full. [pdf]